Square Newspaper Weave Basket

SAM_2081

I wanted some baskets for my fabric stash. When it comes to fabric I am a hoarder and have loads of tiny pieces that I use for applique. So here is how I made them, please read all the instructions before starting this project:

Newspaper Sticks

SAM_2091

You will need lots of newspaper sticks. There are quite a few websites showing how to make these, my particular favourite is this video: https://www.youtube.com/watch?v=ZXHKvQbMJO0
I do sell them in my Etsy shop but postage is quite expensive.

It does take a while to master this, don’t give up, after all you will only be wasting old newspapers whilst you practice. In the video she uses white glue (PVA glue), I use a glue stick which works just the same but dries quicker. And I cut my newspaper with scissors.

A Mould
Measure the size of basket you want to weave and make a mock up, or mould, of one out of cardboard. Make the mould approx 1″ smaller than the size you want your finished basket to be. You will use this to weave round, it will help you to keep the size and shape of your basket as you will see further on in this tutorial.

Start Making Your Basket
Using your mould as a template draw round the bottom onto another piece of cardboard. ( I have used a thick piece of cardboard from a flat pack furniture delivery box, you could glue together several pieces of thin cardboard to make it thicker).

Cut it out.
This piece will be the beginning of your basket.

SAM_2057

Now to start making your basket. (Mine is quite large 15″ x 15″ x 12″ deep but you can use this tutorial for any size you want).

Draw a line on all four sides of the piece of cardboard you have just cut out for the bottom of your basket, approx 1/2″ in from the edge. Measure and mark approx 1″ apart along each edge making sure to mark at each corner. Don’t be too worried about this measurement as long as they are evenly distributed along each edge.

Next, using a screwdriver or something similar, push through each mark you have made making a hole large enough to take a newspaper stick. I started with an awl and then pushed a biro through each hole to enlarge it.

Take a newspaper stick, fold it in half and poke one end through one of the holes, with the other end of the newspaper stick poke it through the next hole. Pull it through tight so the loop lies flat, as in the picture below. Keep adding sticks until each hole has been filled.

SAM_2058

Turn the cardboard bottom over and these will be the sticks that you will be weaving on, the uprights.

SAM_2059

For my basket I use the rope weave, which uses two newspaper sticks at a time. this video shows you how to make a different bottom, but also shows, very simply, how to do the rope weave.

Weave one row all around the outside of the bottom piece of cardboard. Making sure you mould the weaving newspaper sticks round each corner.

SAM_2060
This is how it should look when you have finished the first row of weaving, turn the whole piece over, as in the picture below

SAM_2061

and carry on weaving making the next row lay on top of the last one while at the same time lifting each upright newspaper stick to make it stand upright. As shown below.:

SAM_2062

When you come to the end of the second row take your mould and place it inside of the upright newspaper sticks.

SAM_2065

Make sure all of your uprights are on the outside of your mould. I like to put something heavy inside the mould so that it doesn’t move around whilst I am weaving. I have used a couple of full paint tins but you could use anything like tins from the food cupboard, stones or bricks from the garden etc.

Now you can carry on weaving, making your weaving as close as possible to your mould. But not too tight that you can’t remove your mould at the end.

SAM_2055

If you find your uprights are too short for the height of your basket, as I have here, you need to make them longer. To do this you need to add more newspaper sticks. Here I have some made from the yellow pages, they are shorter than the newspaper sticks but long enough to reach the top of my measured basket.

SAM_2069

To make the uprights longer I insert more paper sticks, with the use of a knitting needle.

SAM_2068
Poke in the knitting needle next to one upright and slightly stretch the weaving and just push in another stick (you could add a small amount of white glue (PVA) if you wish). You will need to add new sticks all the way round. Be careful not to pull out these extra sticks as you are weaving.

SAM_2072

Carry on weaving incorporating these new sticks as shown.

When you have reached the height that you want your basket to be you need to close your weaving.

Take each end of your two weaving sticks and using a knitting needle or similar, prize open about three rows down and push down one end, pulling it right through, do the same with the other end.

SAM_2076

SAM_2077

So they look like this. Cut off the excess.

SAM_2078

You have now finished weaving your basket. To complete, cut off all the uprights flush to the edge of the basket. Like so:

SAM_2079

 

SAM_2056

In the next tutorial I will show you how I finish and paint my newspaper weave baskets.

Advertisements

One thought on “Square Newspaper Weave Basket

  1. Pingback: 36 Tutorials for Weaving a Basket out of Newspaper | Guide Patterns

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s